Alfoele non so a cosa possano servirti ma su linea fw con ma5671a (fw carlito) sono praticamente identici:
status overview
chip version (fuse format) A22 (1)
driver version (otop version) 7.5.1 (7.5.1.0)
state history 9 8 4 3 2 1 6 0 0 0
config reads + + + + + + + +
table reads + + + + +
PLL lock status locked
Signal detect true
manage mode (OMU/BOSA/BOSA2), powerlevel BOSA, low (1)
manual mode, BERT mode, BOSA loop mode off, off, dual-loop
laser age (active time) 0:00:00
laser temperature (ext corr): 315K
die temperature (int corr) 332K
rx offset correction 0
maximum bias / modulation current (chip) 78.00mA / 95.00mA
precalc. bias / modulation current 8.33mA / 16.39mA (6)
actual bias / modulation current 8.80mA / 9.28mA
bias / modulation change (errors) stable / stable (0 / 1)
integration coefficient bias / modulation 7 / 7
gain correction factor P0 / P1 1.10 / 1.11
MPD target P0 / P1 +518 / +2643
MPD actual P0 / P1 (variation to target) n/a
current offset 163.09uA
RSSI 1490 voltage, current 864.75mV 864.75uA
RSSI 1550 voltage 499.02mV
RF 1550 voltage 498.72mV
DDMI voltage 3168.33mV
RSSI 1490 power 86.37uW -10.61dBm
tx power (se*(bias+mod/2-ith)) 0.66mW -1.82dBm
precalc. dcdc apd voltage, saturation 42.10V 164 (4)
DCDC APD target voltage (active/inactive) 42.10V (active)
DCDC APD voltage (regulation error), saturation 41.98V (+0.00V) 164
linear LDO converter (active/inactive) (inactive)
monitor calibrated settings
power level: 180/3820uW 90/1910uW * 45/ 955uW manual
tia gain sel (0xF653): 2 (9.4) 3 (29.0) 3 (29.0) inval
MPD reference current: 1mA (3) 100uA (2) 100uA (2) inval (0)
gain correct factor P0: 1.059 1.096 1.000 0.000
gain correct factor P1: 1.110 1.110 1.000 0.000
scale factor Imod: 1.000 1.000 1.000 0.000
P0 MPD gain reference: 3929 1159 1185 0
P1 MPD gain reference: 3852 1155 1174 0
P0 MPD target ref.: 326 456 312 0
P1 MPD target ref.: 1713 2381 1244 0
crosstalk coefficient: + 4.32mA +14.32mA +14.88mA + 0.00mA
MPD offset c/f: 1/30 0/94 0/0 0/0
P0 delta offset c/f: -2/-18 -4/-6 0/0 0/0
P1 delta offset c/f: 1/1 1/4 0/0 0/0
MPD coarse/fine ratio: 34.22 95.51 116.00 0.00
P0 coarse/fine ratio: 20.05 19.95 20.00 0.00
P1 coarse/fine ratio: 20.33 20.20 20.00 0.00
status overview
chip version (fuse format) A22 (1)
OPTION VALUE
PLOAM state 5
Downstream FEC enable no
Upstream FEC enable no
PLOAMd message waiting in buffer no
PLOAMd message buffer overflow no
Receive state machine status sync
Receive superframe state machine status sync
PEE received no
ONU ID 12
Start Offset enable no
[0] Interface mode 15
[0] PHY status 5
[0] PHY duplex 1
[0] WOL status 0
