Volevo chiudere la discussione aggiungendo per i posteri che alla fine ho attivato una linea TIM senza modem, ho configurato il Technicolor con bridge tra ptm0.835 e eth0, pfSense adesso si connette e naviga che è una meraviglia. Tra l'altro per il VoIP non c'è bisogno di ulteriori connessioni su VLAN differenti.
Chiesto i dati di configurazione del VoIP al Servizio Clienti, configurato FreePBX e va anche quello.
Avevo provato a collegarmi alla seriale della VS, ma credo che il firmware disattivi l'RX, quindi non c'è stato modo di bloccare il boot. Penso che in ogni caso non ci sarebbe stato nemmeno modo di avviare una shell.
Il connettore della seriale è J4, con il seguente pinout: 1GND (triangolino bianco) 2TX 3VCC 4RX
Di seguito il bootlog, la VS è una SH3000-CM220 v1.6:
----
BTRM
V1.6
PMCS
AFEL
PWRZ
MEML
PMCD
MEMP
CODE
ZBSS
MAIN
CACH
OTP?
OTPP
ROTB
SCBT
NAND
IMG?
IMGL
HDR?
HDRP
MCV?
KEY?
KEYA
MID?
MIDP
MCVA
SBI?
SBIA
PASS
----
HELO
4.1605-1.0.38-118.3
CPU0
PMCM
PMCS
AFEL
PWRZ
MEML
APMT
PMCD
L1CD
MMUI
CODE
ZBBS
MAIN
NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
DRAM
MCB chksum 0xf53f590b
DDR3-1600 CL11 512MB High Temperature ASR
Changed Byte Lane LDE
Changed Byte Lane LDE
PASS
NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
FPS0
FDPM
PMOK
GFOK
F002
RAM1
NAN9
NAN3
RFS0
BTL?
BTLA
PASS
FKOK
GKOK
NAN5
Base: 5.2_03patch1xpon
CFE version 1.0.38-161.189 for BCM963138 (32bit,SP,LE)
Build Date: Fri Sep 28 10:56:11 CST 2018 (jeremy@Ubuntu)
Copyright (C) 2000-2015 Broadcom Corporation.
Boot Strap Register: 0x7dfffc2f
Chip ID: BCM63136_B0, ARM Cortex A9 Dual Core: 1000MHz
Total Memory: 536870912 bytes (512MB)
NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
NAND flash device: , id 0xc2da block 128KB size 262144KB
pmc_init:PMC using DQM mode
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Default host ramdisk file name :
Default ramdisk store address :
Default DTB file name :
Board Id : 963138REF
Number of MAC Addresses (1-64) : 16
Base MAC Address : 80:16:05:(rimosso)
PSI Size (1-128) KBytes : 48
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
MC memory allocation (MB) : 4
TM memory allocation (MB) : 48
DHD 0 memory allocation (MB) : 14
DHD 1 memory allocation (MB) : 14
DHD 2 memory allocation (MB) : 0
WLan Feature : 0x00
Voice Board Configuration (0-28) : LE9642_ZSI_BB
Partition 1 Size (MB) :
Partition 2 Size (MB) :
Partition 3 Size (MB) :
Partition 4 Size (MB) (Data) : 4MB
Initalizing switch low level hardware.
pmc_switch_power_up: Rgmii Tx clock zone1 enable 0 zone2 enable 0.
Software Resetting Switch ... Done.
Waiting MAC port Rx/Tx to be enabled by hardware ...Done
Disable Switch All MAC port Rx/Tx
SC_DEBUG: Nand Partition Table Magic Found at c0000.
Enable Switch MAC Port Rx/Tx, set PBVLAN to FAN out, set switch to NO-STP.
RDP TM memory = 20MB, MC memory = 4MB : Max Possible Bufs <8192> of size <2048>; Allocating <7680> bufs; RDP enum <2>
Creating CPU ring for queue number 0 with 32 packets descriptor=0x00f82fb0, size_of_entry 16
Done initializing Ring 0 Base=0x42a1ba60K End=0x42a1bc60K calculated entries= 32 RDD Base=2a1ba60K descriptor=0x00f82fb0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
***************************************************
Sercomm Boot Version 4.0.1.0, at Sep 28 2018, 10:56:13
***************************************************
Find bootFlag successfully.
Booting from first image (0x00a40000) ...
KFS Authenticate ... OK!
LIB Authenticate ... OK!
Checksum ... OK!
Decompression Image.Src Addr:0x2f89d70,Des Addr:0x8000
Decompression LZMA Image OK!
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
/memory = 0x20000000 bytes @ 0x0
Appending NVRAM to dtb, ret:0
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 4.1.38+ (west@ubuntu) (gcc version 5.3.0 (Buildroot 2016.02) ) #1 SMP PREEMPT Fri Jun 25 12:11:25 CST 2021
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Broadcom BCM963138
Reserved memory: phys 0x0fd00000 size 0x00300000 for adsl
Reserved memory: phys 0x0cc00000 size 0x03000000 for tm
Reserved memory: phys 0x0c800000 size 0x00400000 for mc
Reserved memory: phys 0x0ba00000 size 0x00e00000 for dhd0
Reserved memory: phys 0x0ac00000 size 0x00e00000 for dhd1
Memory policy: Data cache writealloc
creating a MT_MEMORY_NONCACHED device at physical address of 0x0fd00000 to virtual address at 0xcfd00000 with size of 0x300000 byte for adsl
creating a MT_MEMORY_NONCACHED device at physical address of 0x0cc00000 to virtual address at 0xccc00000 with size of 0x3000000 byte for tm
creating a MT_MEMORY_NONCACHED device at physical address of 0x0c800000 to virtual address at 0xcc800000 with size of 0x400000 byte for mc
creating a MT_MEMORY_NONCACHED device at physical address of 0x0ba00000 to virtual address at 0xcba00000 with size of 0xe00000 byte for dhd0
creating a MT_MEMORY_NONCACHED device at physical address of 0x0ac00000 to virtual address at 0xcac00000 with size of 0xe00000 byte for dhd1
creating a MT_MEMORY_NONCACHED device at physical address of 0x0ab00000 to virtual address at 0xcab00000 with size of 0x100000 byte for Kernel Crash
pmc_init:PMC using DQM mode
pmc_init:ffc4 3420348 4b004b
PERCPU: Embedded 11 pages/cpu @dfb5a000 s15616 r8192 d21248 u45056
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 108416
Kernel command line: console=ttyS0,115200 root=mtd:rootfs ro rootfstype=jffs2 irqaffinity=0 coherent_pool=1M cpuidle_sysfs_switch
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 426988K/438272K available (4732K kernel code, 323K rwdata, 1304K rodata, 200K init, 275K bss, 11284K reserved, 0K cma-reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc05ed27c (6037 kB)
.init : 0xc05ee000 - 0xc0620000 ( 200 kB)
.data : 0xc0620000 - 0xc0670e60 ( 324 kB)
.bss : 0xc0670e60 - 0xc06b5b10 ( 276 kB)
Preemptible hierarchical RCU implementation.
NR_IRQS:256
Cortex A9 MPCORE GIC init
DIST at fc01f000, CPU_IF at fc01e100
L2C: platform modifies aux control register: 0x02070000 -> 0x6a450000
L2C: DT/platform modifies aux control register: 0x02070000 -> 0x6a450000
L2C: DT/platform tries to modify or specify cache size
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 I prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 512 kB
L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x6e450001
map_hw_timer_interrupt,127: interrupt_id 96
map_hw_timer_interrupt,127: interrupt_id 97
map_hw_timer_interrupt,127: interrupt_id 98
map_hw_timer_interrupt,127: interrupt_id 99
clocksource timer_cs: mask: 0x3fffffff max_cycles: 0x3fffffff, max_idle_ns: 9556302227 ns
sched_clock: 30 bits at 50MHz, resolution 20ns, wraps every 10737418230ns
console [ttyS0] enabled
Calibrating delay loop... 1325.05 BogoMIPS (lpj=662528)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Initializing cgroup subsys blkio
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
Broadcom Logger v0.1
Setting up static identity map for 0x8220 - 0x8254
Brought up 2 CPUs
SMP: Total of 2 processors activated (2655.23 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
NET: Registered protocol family 16
DMA: preallocated 1024 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
Successfully retrieved NVRAM data from dtb
Failed to retrieve boot CFE version from dtb!
irq: no irq domain found for /interrupt-controller@80000000 !
++++ Powering up USB blocks
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skb_free_task created successfully with start budget 256
gbpm_do_work scheduled
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 initialized
Broadcom GBPM v0.1 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Switched to clocksource timer_cs
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
futex hash table entries: 512 (order: 2, 16384 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
ntfs: driver 2.1.32 [Flags: R/W].
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
io scheduler noop registered (default)
brd: module loaded
loop: module loaded
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=26152300, chipSelect=0
brcmnand_read_id: CS0: dev_id=c2da9095
After: NandSelect=00000001, nandConfig=26152300
DevId c2da9095 may not be supported. Will use config info
Spare Area Size = 16B/512B
Block size=00020000, erase shift=17
NAND Config: Reg=26152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
ECC level changed to 4
OOB size changed to 16
BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 256MB on CS0
Found NAND on CS0: ACC=c3840010, cfg=26152300, flashId=c2da9095, tim1=65324458, tim2=80000e54
BrcmNAND version = 0x80000700 256MB @00000000
brcmnand_scan: B4 nand_select = 00000001
brcmnand_scan: After nand_select = 00000001
handle_acc_control: default CORR ERR threshold 3 bits
ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
Brcm NAND controller version = 7.0 NAND flash size 256MB @10000000
ECC layout=brcmnand_oob_bch4_2k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
brcmnand_reset_corr_threshold: default CORR ERR threshold 3 bits for CS0
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_eem
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-platform: EHCI generic platform driver
ehci-platform ehci-platform.0: EHCI Host Controller
ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform.0: irq 105, io mem 0x8000c300
ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-platform: OHCI generic platform driver
ohci-platform ohci-platform.0: Generic Platform OHCI controller
ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
ohci-platform ohci-platform.0: irq 104, io mem 0x8000c400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
i2c /dev entries driver
brcmboard registered
brcmboard: brcm_board_init entry
print_rst_status: Last RESET due to POR reset
DYING GASP IRQ Initialized and Enabled
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xfffe8600 (irq = 64, base_baud = 921600) is a BCM63XX
ttyS1 at MMIO 0xfffe8620 (irq = 65, base_baud = 921600) is a BCM63XX
I2C SFP Module Driver Loaded
BPM: tot_mem_size=536870912B (512MB), buf_mem_size <15%> =80530635B (76MB), num of buffers=39945, buf size=2016
Broadcom BPM Module Char Driver v0.1 Registered<3004>
PCIe HCD (impl1)
bcm963xx-pcie: found core [0] Rev [3.01] with 1 Lanes
bcm963xx-pcie bcm963xx-pcie.0: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers disabled
pci 0000:00:00.0: BAR 8: assigned [mem 0x90000000-0x905fffff]
pci 0000:01:00.0: BAR 2: assigned [mem 0x90000000-0x903fffff 64bit]
pci 0000:01:00.0: BAR 0: assigned [mem 0x90400000-0x90407fff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x90000000-0x905fffff]
pcieport 0000:00:00.0: enabling device (0140 -> 0142)
pcieport 0000:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512
pci 0000:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512
bcm963xx-pcie: found core [1] Rev [3.01] with 1 Lanes
bcm963xx-pcie bcm963xx-pcie.1: PCI host bridge to bus 0001:00
pci_bus 0001:00: root bus resource [mem 0xa0000000-0xafffffff]
pci_bus 0001:00: root bus resource [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers disabled
pci 0001:00:00.0: BAR 8: assigned [mem 0xa0000000-0xa0bfffff]
pci 0001:00:00.0: BAR 9: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref]
pci 0001:01:00.0: BAR 2: assigned [mem 0xa0000000-0xa07fffff 64bit]
pci 0001:01:00.0: BAR 4: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref]
pci 0001:01:00.0: BAR 0: assigned [mem 0xa0800000-0xa0807fff 64bit]
pci 0001:00:00.0: PCI bridge to [bus 01]
pci 0001:00:00.0: bridge window [mem 0xa0000000-0xa0bfffff]
pci 0001:00:00.0: bridge window [mem 0xa0c00000-0xa0cfffff 64bit pref]
pcieport 0001:00:00.0: enabling device (0140 -> 0142)
pcieport 0001:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512
pci 0001:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512
GACT probability NOT on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (6671 buckets, 26684 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
L2TP core: blog_l2tp_rcv_check
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Registering SWP/SWPB emulation handler
random: nonblocking pool is initialized
VFS: Mounted root (jffs2 filesystem) readonly on device 31:6.
Freeing unused kernel memory: 200K (c05ee000 - c0620000)
ubi0: attaching mtd9
ubi0: scanning is finished
ubi0: attached mtd9 (name "package", size 80 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 640, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 348497453
ubi0: available PEBs: 0, total reserved PEBs: 640, PEBs reserved for bad PEB handling: 13
ubi0: background thread "ubi_bgt0d" started, PID 451
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 456
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "package"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 77709312 bytes (74 MiB, 612 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID EB59AD70-F281-4D35-811B-321ECEF4EC40, small LPT model
rdpa: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
tm_base_addr 0xccc00000, size 50331648, tm_base_addr_phys 0x0cc00000
mc_base_addr 0xcc800000, size 4194304, mc_base_addr_phys 0x0c800000
RDP reserved memory has been adjusted
TM: base_addr = 0xcd000000, phys_addr = 0x0d000000, size = 34MB
MC: base_addr = 0xcc800000, phys_addr = 0x0c800000, size = 8MB
RDP TM memory = 34MB, MC memory = 8MB : Max Possible Bufs <19660> of size <2048>; Allocating <15360> bufs; RDP enum <5>
WARNING!RDP reserved memories are wasting 10MB of memory, please adjust your reserved memory size
++++Runner gso_desc_pool created successfully
brcmchipinfo: brcm_chipinfo_init entry
bcmxtmrt: Broadcom BCM3136B0 ATM/PTM Network Device v0.9
Created XTM Rx queue 5 with size 256,Descriptor base=00c1a000
Created XTM Rx queue 6 with size 256,Descriptor base=00c1c000
NBUFF v1.0 Initialized
Total # of labels = 62
Initialized fcache state
Broadcom Packet Flow Cache Char Driver v4.0 Registered<3002>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
[FHW] pktDbgLvl[0xbf342424]=0
[FHW] fhw_construct:
Initialized Fcache HW accelerator layer state
flwStatsThread created. numFlwsPerPoll 546 maxFlwIdx 16383
Constructed Broadcom Packet Flow Cache v4.0
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#0
Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#1
Switch Port#3 (Internal MUX Port#0) connects to Crossbar Port#4
Unused MUX Internal Port#1 connects to Crossbar External Port#2
Cross Bar MUX Config : Internal Port 00 maps to External Port 04 <reg_val : 0x0000000c>
Cross Bar MUX Config : Internal Port 01 maps to External Port 02 <reg_val : 0x00000014>
Cross Bar MUX Config : Internal Port 02 maps to External Port 00 <reg_val : 0x00000014>
Cross Bar MUX Config : Internal Port 02 maps to External Port 00 <reg_val : 0x00000014>
GPIO 36 is assigned to Serdes Fiber Signal Detection.
Setting SGMII Calibration value to 0x8
GPIO Pin -32731 is configured as SPF MOD_ABS for module insertion detection
Broadcom BCM63136_B0 Ethernet Network Device v0.1
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
++++ disabling GSO on logical_port=0 dev=eth0
eth0: <Int sw port: 0> <Logical : 00> MAC : 80:16:05:(rimosso)
Chip Physical Port 9, Cross Bar Port 0, PHY_ID <0x06180006:0x06:Serdes PHY >
Chip Physical Port 10, Cross Bar Port 1, PHY_ID <0x0007f00c:0x0c:Internal PHY >
eth1: <Ext sw port: 0> <Logical : 08> PHY_ID <0x0007f008:0x08:Internal PHY> MAC:80:16:05:(rimosso)
eth2: <Ext sw port: 1> <Logical : 09> PHY_ID <0x0007f009:0x09:Internal PHY> MAC:80:16:05:(rimosso)
eth3: <Ext sw port: 2> <Logical : 10> PHY_ID <0x0007f00a:0x0a:Internal PHY> MAC:80:16:05:(rimosso)
eth4: <Ext sw port: 3> <Logical : 11> MAC : 80:16:05:(rimosso)
Chip Physical Port 13, Cross Bar Port 4, PHY_ID <0x0007f00b:0x0b:Internal PHY >
Ethernet Auto Power Down and Sleep: Enabled
Cross bar port 1 of Int switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00
Ext switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00
Ext switch port 1; Adv capability change : MII=0x01e1, GMII=0x0f00
Ext switch port 2; Adv capability change : MII=0x01e1, GMII=0x0f00
Cross bar port 4 of Ext switch port 3; Adv capability change : MII=0x01e1, GMII=0x0f00
All Port Bit Map: 0x0f01: eth0,eth1,eth2,eth3,eth4
Chip WAN Only Ports 0001, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0001:eth0
Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000:
Chip LAN Only Ports 0f00, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0f00:eth1,eth2,eth3,eth4
WAN/LAN Both Capable Ports 0x0000:
Created Ethernet Rx queue 4 with size 512, Descriptor base=00c1e000
Created Ethernet Rx queue 3 with size 512, Descriptor base=00c21000
===> Activate Deep Green Mode
Initialized Runner Host Layer
Initialized Runner Unicast Layer
Initialized Runner L2 Unicast Layer
Initialized Runner Multicast Layer
Broadcom Packet Flow Cache HW acceleration enabled.
Enabled Runner binding to Flow Cache
Initialized Runner Protocol Layer (700)
Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009>
NComm TMS V6.90 Kernel Module loaded.
Broadcom 802.1Q VLAN Interface, v0.1
brcm_otp_init entry
Initializing WLCSM Module
WLCSM Module loaded successfully
Wifi Forwarding Driver is initialized!
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
PPTP driver version 0.8.5
DHD_FKB_POOL size is:1280 and entry size:2016
fkbpool address range: d8400000 <-> d8676000
DHD_PKTTAG POOL size is:1280 and entry size:64
dhd_module_init in
dhd_queue_budget = 256
dhd_sta_threshold = 2048
dhd_if_threshold = 65536
no wifi platform data, skip
PCI_PROBE: bus 1, slot 0,vendor 14E4, device AA52(good PCI location)
dhdpcie_init: can't find adapter info for this chip
pcieh 0000:01:00.0: enabling device (0140 -> 0142)
DHD: dongle ram size is set to 983040(orig 983040) at 0x180000
dhd:0: fw path:(null) nv path:(null)
dhd_runner_attach: Tx Offload - Enabled, Ring Size = 1024
dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
TX wakeup info: reg = <0x80299004>, val = <0x10000000>
RX wakeup info: reg = <0x8029a004>, val = <0x28000000>
dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0)
dhd_attach(): thread:dhd_watchdog_thread:22a started
dhd_attach(): thread:dhd0_dpc:22b started
dhd_deferred_work_init: work queue initialized
dhd_macdbg_attach: psvmpmems d88d5a80 svmpmems_sz 13
Creating CPU ring for queue number 0 with 1024 packets descriptor=0xbf4f275c
Creating CPU ring for queue number 1 with 1024 packets descriptor=0xbf4f2778
wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3
Instantiating WFD 0 thread
dhd:0: fw path:(null) nv path:(null)
dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path=
update_firmware_path: pfw_path = /etc/wlan/dhd
_dhdpcie_get_nvram_params: fail to read nvram from flash.
dhdpcie_ramsize_adj: Enter
dhd_bea_read_header: Not a .bea header
dhdpcie_download_code_file: download firmware /etc/wlan/dhd/43602a3/rtecdc.bin
dhd_bea_read_header: Not a .bea header
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=pci/0/1/0/
wl: ID=pci/0/1/0/
wl: loading /etc/wlan/bcm43602_map.bin
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19
wl: reading /etc/wlan/bcm43602_nvramvars.bin, file size=15
dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
PCIe shared addr (0x001b7d48) read took 35023 usec before dongle is ready
DMA RX offset from shared Area 0
dhdpcie_readshared: Dongle advertizes 2 size indices
dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it
H2D DMA WR INDX : array size 384 = 2 * 190
D2H DMA RD INDX : array size 32 = 2 * 3
D2H DMA WR INDX : array size 32 = 2 * 3
H2D DMA RD INDX : array size 384 = 2 * 190
ring_info_raw: 56
1c 9f 26 00 2c ab 26 00 a8 ac 26 00 24 ae 26 00
2a ae 26 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 be 00 00 00
dhdpcie_readshared: max H2D queues 190
dhd_bus_start: Initializing 190 h2drings
dhd_runner_flowmgr_init: dhd0_rnr bootmem addr<cba00000> size<14680064>
dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512
dhd_runner_policy_init: N+M Policy = 0 1 (HW)
dhd_bus_cmn_writeshared:
0000: 00 10 53 1f 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 fa 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 a0 b3 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 80 fa 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 fb 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 00 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 10 14 00
dhd_bus_cmn_writeshared:
0000: 00 48 8f 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 4c 8f 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 40 8f 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 44 8f 18 00 00 00 00
Attach flowrings pool for 188 rings
Runner DHD PCIE: vendor<0x14e4> device<0xaa52> bus<1> slot<0>
Initial configuration
=================================
rx_post_flow_ring_base_addr : c0fa0000
tx_post_flow_ring_base_addr : cb9c4000
rx_complete_flow_ring_base_addr : c0fb0000
tx_complete_flow_ring_base_addr : c0fa8000
r2d_wr_arr_base_addr : e12a1000
d2r_rd_arr_base_addr : e12a1402
r2d_rd_arr_base_addr : e12a1c00
d2r_wr_arr_base_addr : e12a1802
tx_post_mgmt_arr_base_addr : e12a2000
tx_post_mgmt_arr_base_phys_addr : 0x188f5000
r2d_wr_arr_base_phys_addr : 0x188f4000
d2r_rd_arr_base_phys_addr : 0x188f4402
r2d_rd_arr_base_phys_addr : 0x188f4c00
d2r_wr_arr_base_phys_addr : 0x188f4802
Doorbell ISR : bf527728
Doorbell CTX : d8865000
Creating CPU ring for queue number 7 with 128 packets descriptor=0xbf2bed9c, size_of_entry 16
Done initializing Ring 7 Base=0xe0833000 End=0xe0833800 calculated entries= 128 RDD Base=c2f000K descriptor=0xbf2bed9c
Runner DHD Offload initialization complete
CUR_ETHERADDR : 6
00 90 4c 17 20 00
dhd_sync_with_dongle: GET_REVINFO device 0x43bb, vendor 0x14e4, chipnum 0xaa52
Dongle Host Driver, version 7.14.170.36.cpe5.02L03.0-kdb
wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0
PCI_PROBE: bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
dhdpcie_init: can't find adapter info for this chip
pcieh 0001:01:00.0: enabling device (0140 -> 0142)
DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000
dhd:1: fw path:(null) nv path:(null)
dhd_runner_attach: Tx Offload - Enabled, Ring Size = 1024
dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
TX wakeup info: reg = <0x80299004>, val = <0x11000000>
RX wakeup info: reg = <0x8029a004>, val = <0x29000000>
dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0)
dhd_attach(): thread:dhd_watchdog_thread:230 started
dhd_attach(): thread:dhd1_dpc:231 started
dhd_deferred_work_init: work queue initialized
dhd_macdbg_attach: psvmpmems da1ead00 svmpmems_sz 13
Creating CPU ring for queue number 2 with 1024 packets descriptor=0xbf4f2794
Creating CPU ring for queue number 3 with 1024 packets descriptor=0xbf4f27b0
Instantiating WFD 1 thread
wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type fkb configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc
dhd:1: fw path:(null) nv path:(null)
dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path=
update_firmware_path: pfw_path = /etc/wlan/dhd
_dhdpcie_get_nvram_params: fail to read nvram from flash.
dhdpcie_ramsize_adj: Enter
dhd_bea_read_header: Not a .bea header
dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000
dhdpcie_download_code_file: download firmware /etc/wlan/dhd/4366c0/rtecdc.bin
dhd_bea_read_header: Not a .bea header
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=pci/1/1/0/
wl: ID=pci/1/1/0/
wl: loading /etc/wlan/bcm43664_map.bin
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19
wl: reading /etc/wlan/bcm43664_nvramvars.bin, file size=148
dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
PCIe shared addr (0x002ae3b4) read took 68023 usec before dongle is ready
DMA RX offset from shared Area 0
dhdpcie_readshared: Dongle advertizes 2 size indices
dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it
H2D DMA WR INDX : array size 544 = 2 * 266
D2H DMA RD INDX : array size 32 = 2 * 3
D2H DMA WR INDX : array size 32 = 2 * 3
H2D DMA RD INDX : array size 544 = 2 * 266
ring_info_raw: 56
18 61 43 00 e8 71 43 00 fc 73 43 00 10 76 43 00
16 76 43 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 0a 01 00 00
dhdpcie_readshared: max H2D queues 266
dhd_bus_start: Initializing 266 h2drings
dhd_runner_flowmgr_init: dhd1_rnr bootmem addr<cac00000> size<14680064>
dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512
dhd_runner_policy_init: N+M Policy = 0 1 (HW)
dhd_bus_cmn_writeshared:
0000: 00 70 4e 1f 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 80 fb 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 be 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 c0 fa 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 fc 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 20 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 10 14 00
dhd_bus_cmn_writeshared:
0000: 00 48 bd 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 4c bd 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 40 bd 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 44 bd 18 00 00 00 00
Attach flowrings pool for 264 rings
Runner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0>
Initial configuration
=================================
rx_post_flow_ring_base_addr : c0fb8000
tx_post_flow_ring_base_addr : cabc4000
rx_complete_flow_ring_base_addr : c0fc0000
tx_complete_flow_ring_base_addr : c0fac000
r2d_wr_arr_base_addr : e12c9000
d2r_rd_arr_base_addr : e12c9402
r2d_rd_arr_base_addr : e12c9c00
d2r_wr_arr_base_addr : e12c9802
tx_post_mgmt_arr_base_addr : e12ca000
tx_post_mgmt_arr_base_phys_addr : 0x18bd5000
r2d_wr_arr_base_phys_addr : 0x18bd4000
d2r_rd_arr_base_phys_addr : 0x18bd4402
r2d_rd_arr_base_phys_addr : 0x18bd4c00
d2r_wr_arr_base_phys_addr : 0x18bd4802
Doorbell ISR : bf527728
Doorbell CTX : da299400
Creating CPU ring for queue number 1 with 128 packets descriptor=0xbf2beba4, size_of_entry 16
Done initializing Ring 1 Base=0xe0841000 End=0xe0841800 calculated entries= 128 RDD Base=c3d000K descriptor=0xbf2beba4
Runner DHD Offload initialization complete
dhd_rx_frame: net device is NOT registered. drop event packet
dhd_rx_frame: net device is NOT registered. drop event packet
CUR_ETHERADDR : 6
00 90 4c 1d 00 00
dhd_sync_with_dongle: GET_REVINFO device 0x43c5, vendor 0x14e4, chipnum 0xaa90
Dongle Host Driver, version 7.14.170.36.cpe5.02L03.0-kdb
wfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1
dhd_module_init out
RDPA DS WAN UDP Filter Command Driver
Broadcom Ingress QoS Module Char Driver v0.1 Registered<3003>
Broadcom Ingress QoS ver 0.1 initialized
[DSPHAL] dsphal_init: Starting DSPHAL driver.
[DSPHAL] pcm_clk_init: starting PCM clock
[DSPHAL] pcm_nco_mux_cfg: using MISC for NCO FCW
[DSPHAL] pcm_nco_init: PCM clock in ZSI mode
[DSPHAL] dh_configure_channel: device 0, channel 0, id 0, devType 40, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0
[DSPHAL] dh_configure_channel: device 0, channel 1, id 1, devType 40, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1
[DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1
[DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1
[SLICSLAC] slicslac_init: Starting SLIC/SLAC driver.
sc_sfp 0-0050: initialized
sc_sfp 0-0051: initialized
I2C SFP Module Driver Loaded
Ethernet Auto Power Down and Sleep: Enabled
Energy Efficient Ethernet: Enabled
[ERROR pktrunner] runnerUcast_inet6addr_event,185: Could not rdpa_ucast_ipv6_host_address_table_find
echo (609): drop_caches: 3
